IPB

Welcome Guest ( Log In | Register )

Announcements
 
Reply to this topicStart new topic
Best aftermarket barrel
post June 8th 2009 6:06 AM
Post #1



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






Hi I am new to this page, although I have been roaming around it the past few months not registered. I am about to make my first 10mm purchase, a g29, and plan to get an aftermarket .40 s&w barrel. My dad just bought a lone wolf for his g23, but it was pretty inaccurate....way less than the factory. I just wanted to know if one drop in barrel was better than another. I was thinking going with storm lake, as they aren't too expensive(college student). Also where is the best place to buy accessories, such as the pearce grip extensions and ammo. I have heard mike at double tap is swamped and not returning email, is this true or should I go ahead and order from him. Also my woods load will be lead most likely, as long as I keep the factory barrel clean is lead ok? sorry for the long post..... i love this site, and it was this site that convinced me to sell the .44 and go 10!

p.s. where do yall buy your barrels?


Signature:
"Keep your nose in the wind and your eye along the skyline."
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 2:35 PM
Post #2



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






Moose, welcome.gif to 10mmTalk!

Well I went with the Storm Lake 40S&W for my G-29 and it has been very accurate and function has been supurb. The chamber has great support and is tight. Beaware of 40S&W brass which is shot from loose chambered, as they develop a bulge on some right at the extactor cut. Standard reloading dies don't get down that far to iron this out, but Redding does make a new "push thru die" that will remove and size the brass down to proper dimentions. This will improve the feeding problems which some people experience using 40's with tight chambers.

Storm Lakehttp://www.stormlakebarrel.com/

Pearce Grips http://www.cheaperthandirt.com/SearchResul...=10&q=PG-29

I hope this helps! Best regards! thumb.gif

Links and References to Other Pages:

http://www.stormlakebarrel.com/
http://www.cheaperthandirt.com...ts&num=10&q=PG-29


Signature:
The
SHADOW

The "10mm" I'm Packin', Has The Bullets Wackin', Smakin' & The Slide is Rackin' & Jackin'!
NRA Life Member
Southeast, LoUiSiAna
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 3:47 PM
Post #3



Group Icon

Group: Members
Member No.: 10,697
Posts: 83
Joined: Mar. 12th 2007
From: Mississippi
Online Status: OFFLINE






The best would probably be a Bar-Sto or a KKM, which I have neither. I got a EFK just because they are only ones that made extended barrel for G29 but accuracy is not that great.
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 4:24 PM
Post #4



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






keith97, I could agree with the KKM, but the Bar-Sto used to be a quality product, some of their stuff has been poorly QC'ed and overly priced. sad.gif

I know there can be good and bad for most companies!
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 4:47 PM
Post #5



Group Icon

Group: Members
Member No.: 8,485
Posts: 295
Joined: Dec. 1st 2008
From: Oregon
Online Status: OFFLINE






Moose welcome.gif Welcome to the "dark side" - enjoy your G20!


Signature:
Fast is fine, but accuracy is final - Wyatt Earp
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 5:11 PM
Post #6



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






Have any of yall done business with topglock or glockworld? I thought about ordering a storm lake barrel from them(only $119), but I have heard bad things about all the sites run by TGSCOM.
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 5:20 PM
Post #7



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






I bought my G-29 and some goodies thru them without any problems. thumbsup.gif
Go to the top of the pagePM
 
+Quote Post
post June 8th 2009 5:28 PM
Post #8



Group Icon

Group: Silver Patron
Member No.: 7,823
Posts: 4,234
Joined: Nov. 3rd 2008
From: Georgia
Online Status: OFFLINE






welcome.gif to the Armory smile.gif


Signature:
QUOTE
" A Nation which does not remember what it was yesterday does not know where it is today."
Robert E. Lee
Go to the top of the pagePM
 
+Quote Post
post June 9th 2009 1:30 AM
Post #9



Group Icon

Group: Members
Member No.: 14,793
Posts: 92
Joined: Apr. 16th 2009
From: new castle co
Online Status: OFFLINE






I have only ordered from them once and due to supply issues my order ended up being split. All of the items listed as in stock were not. The first half of my order shipped in about 10 days. No big problem with that but the second half after they packaged it for shipment they totally forgot about. It took several calls and about a month wait before it finally shipped.
Go to the top of the pagePM
 
+Quote Post
post June 9th 2009 3:05 AM
Post #10



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






QUOTE (The_Shadow @ June 8th 2009 9:35 AM) *
Moose, welcome.gif to 10mmTalk!

Well I went with the Storm Lake 40S&W for my G-29 and it has been very accurate and function has been supurb. The chamber has great support and is tight. Beaware of 40S&W brass which is shot from loose chambered, as they develop a bulge on some right at the extactor cut. Standard reloading dies don't get down that far to iron this out, but Redding does make a new "push thru die" that will remove and size the brass down to proper dimentions. This will improve the feeding problems which some people experience using 40's with tight chambers.

Storm Lakehttp://www.stormlakebarrel.com/

Pearce Grips http://www.cheaperthandirt.com/SearchResul...=10&q=PG-29

I hope this helps! Best regards! thumb.gif


Shadow, what kind of groups are you getting out of that 40 s&w storm lake barrel?

Links and References to Other Pages:

http://www.cheaperthandirt.com...ts&num=10&q=PG-29
Go to the top of the pagePM
 
+Quote Post
post June 10th 2009 1:59 AM
Post #11



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






QUOTE (Moose @ June 8th 2009 10:05 PM) *
Shadow, what kind of groups are you getting out of that 40 s&w storm lake barrel?


Shooting with the 40S&W Storm Lake conversion barrel in the G-29 I put 30 rounds inside a 4" circle at 40 Yards, these were handloaded Lyman 175 gr TCBB cast bullets with 8.4 grains of Blue Dot @ 1030 fps adv. This I consider pretty damn good for a 3.78" barreled pistol with open sights.
Go to the top of the pagePM
 
+Quote Post
post June 11th 2009 1:49 PM
Post #12



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






I am about to order my g29 the end of this week. I am getting the night sites, are the glock night pretty good or should I put the extra 60 bucks towards another brand? And Shadow, how do you have your g29 set up? Any aftermarket stuff besides the barrel? I was particularly wondering if I should replace the recoil spring with a heavier one. I am of the mindset that glock makes very reliable pistols(above average), so why replace something that glock engineers deemed adequate. Correct me if I am wrong, and if added parts would enhance my pistol or make it more reliable.
Go to the top of the pagePM
 
+Quote Post
post June 11th 2009 3:08 PM
Post #13



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






Moose, Currently I have it set up with the Wolff Gun Springs (non)captured recoil system, this is a two piece recoil rod and dual spring set up. The spring rate is 21lb for this set up. The 23lb I find too heavy, even the 21lb is fairly heavy.
I carry the pistol with the 21lb recoil system & Factory 10mm barrel, with 200grain Hornady @ 1180fps.

It needs to be understood that the use of the heavy springs will make it tougher to rack the slide, to clear malfunctions or jams in a stressful situation.

I don't have Night sights, according to most self defense courses, there is about a 20 minute window of time, early morning or evening which the night sights provide benefits. In extreme low light they can obscure your vision beyond the sights. ohmy.gif Unless you are hunting during this time, you would be better off with a good Flash Light either mounted or hand held for target ID and acquisition.


Best regards! Stay safe! thumb.gif
Go to the top of the pagePM
 
+Quote Post
post June 15th 2009 2:39 AM
Post #14



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






Just got my g29 in today, woohoo!!! Was wondering if I put a 29 lb spring in her, will i have any trouble shooting less powerful loads or even .40 s&w loads when i get a conversion barrel? (will I have to change the spring everytime i put the .40 barrel in)
Go to the top of the pagePM
 
+Quote Post
post June 15th 2009 2:51 AM
Post #15



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






Moose, I can answer that for you, I use the Wolff 21lb spring and their non captured recoil rod in my Glock 29, I also used it with the Storm Lake 40S&W conversion barrel with my reloads without any problems. This is mostly with 175 grain cast going 1035fps as measured over the Chrony.

I hope this helps! Best regards and congratulations! thumb.gif
Go to the top of the pagePM
 
+Quote Post
post June 15th 2009 3:10 AM
Post #16



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






oops meant to say 21 lb spring in my last post not 29! Guess I am just all keyed up and 29 is the only number running through my head...as in G29!!! Thanks for all of the info shadow!
Go to the top of the pagePM
 
+Quote Post
post June 15th 2009 3:12 AM
Post #17



Group Icon

Group: 10mm Staff
Member No.: 10,723
Posts: 1,997
Joined: Mar. 27th 2007
From: Southeastern, LoUiSiAna
Online Status: OFFLINE






I had kind of figured that about your spring number!

And you are quite welcomed!
Go to the top of the pagePM
 
+Quote Post
post June 15th 2009 3:17 AM
Post #18



Group Icon

Group: Members*
Member No.: 15,546
Posts: 14
Joined: Jun. 8th 2009
From: Greenville, SC
Online Status: OFFLINE






one more thing, what are the advantages of the non-captured guide rods and why did glock opt for the captured ones on stock guns?
Go to the top of the pagePM
 
+Quote Post

Reply to this topicStart new topic

Active Members
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
 


Information Center
RSS Lo-Fi Version Time is now: November 21st 2009 12:06 PM